Same bottle, same method.
Become a Patron!
Squonkers are Bonkers
- Thread starter DogMan
- Start date
I wish they were, then I'd have a use for them.. Just look at that bottle .. Look at it! *shakes head*
almost matches your finger
Does the voltage meter still work on a modified noisy Cricket 2 25? Does it let you crank more volts out of a single battery than a straight up Mech squonker? Or would it just modulate down from 4.2 volts?
Sent from my SM-G892A using Tapatalk
It can put out ~75 Watts. Some end users measured the output of the device and it's surprise them to learn that there was no cap at 50 Watts. I had no interest in it because of the wattage cap, but now that I know that the wattage cap was FAKE NEWS
Sent from my SM-G892A using Tapatalk
I personally didn't like how they rounded the contact point on that mod to fit against the 510...everything would have to align perfectly for it to be really beneficial.
If the issue you are having is that its not square when it contacts with the nut, bend it so it does. If your issue is a sloppy button, again bend the vertical part of the contact so it remedies the slop, then change the pitch angle of the point of contact to hit correctly.
$40 for a complete setup is more than enough to get you super high quality vaping performance and any more money spent is in the great scheme somewhat negligible wrt Improving of The Vaping experience. A custom power curve plus of vapors preferred build with more battery power behind it and you could possibly want to use... even if there's some inefficiency in the output, it's not going to result in a bad vaping experience. But there's definitely a lot of enjoyment in trying out new ways of vaping. And if you vape a lot it's worth spending a little bit of extra money on it because you hold it in use it almost as often as your smartphone (perhaps more I don't know you you was probably the wrong pronoun to use LOL)
Sent from my SM-G892A using Tapatalk
The mod is firing fine now. The button issue isn't to contact issue it's making very good contact all the way around the arch (really annoying that there's an arch tear and the name of the electric stuff is also Arch). The plastic button gets stuck coming back into place after firing
Sent from my SM-G892A using Tapatalk
No your in Parrarel mode , on single cell otherwise mod wouldn't work , since goes off bottom plate as well as PCB it works as same as switchfet type , but has reverse protection wont fire if cell is in wrong way ,keeps led on fire switch an flashing if cell drained or other problems TBH is pretty good , I own fet sqounker mods an this NC v2 Rocks its as good as any other good one,
Very good output performance is good , Size and rounded edges/shape make it much more comfortable that the square mods, good build construction good chip,
Feels like an expensive mod
but obviously is a lot cheaper than the higher end ones. But around same cost a god mid range due to extra parts your adding , all in all its one of my favourite mods , because its cheap i dont have to baby it an worry about taking it out if anything break buy another swap parts over simple ,
Sent from my ONEPLUS A3003 using Tapatalk
Last edited:
I thought just the opposite on mine.I have 2 of the original ones from when they first came out,and just got a black one a few days ago,on my 2 originals,i have to close the airflow down to about 2/3 open,but the black one i have wide open,maybe it just comes down to that great QC we all know Chinese companies have haha.
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
I wish they were, then I'd have a use for them.. Just look at that bottle .. Look at it! *shakes head*
That is lovely
I'll have to figure out how to convert mine to squonker
Sent from my SM-G892A using Tapatalk
Well I done did it. Purple Luna on the way. So that makes three with the hybrid Stinger and the US Modz Humble Bee mech I won. Think I’m good on mods for a bit... 
Sent from my iPhone using Tapatalk Pro
Sent from my iPhone using Tapatalk Pro
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Floris finally accepted a pic to engrave. Just a silhouette of ally's black standard poodle.
Thoughts? It's not as grand as I had hoped.
I actually like it - not my kind of colors - but what a neat gift, I'd be flattered and impressed if it was for me and that was my dog
I think that whatever that adhesive material is that connects the button to the metal is causing the button problem. I fiddled with it a bit and I think it's working slightly better.
The "arching" came right out using hand sanitizer and toilet paper
Sent from my SM-G892A using Tapatalk
The "arching" came right out using hand sanitizer and toilet paper
Sent from my SM-G892A using Tapatalk
Last edited:
Ecig Vapor Store has the Pico Squeeze listed for Less than $16.
https://www.ecigvaporstore.com/product/ismoka-eleaf-istick-pico-squeeze-kit/ref/4/
Use code (vapecrawler10) to grab 1 for $14.31
And yes they do have them in White.
Arcing = Not good
What is so hard to understand about that?
Don't give it too deep of a cleaning or you'll strip the coating.If you strip that your mod/device will hit about as well as a wet noodle.
The entire kit for less than FT sells just the mod, and from a US based company?! I know the Coral RDA is pretty mediocre, but at that price I’m tempted to order it just because it’s so cheap. I just don’t know if I realistically need a second Squeeze or how I’d use it. Guess I could throw my incoming Pulse 22 on it.
Oh dear!I wish they were, then I'd have a use for them.. Just look at that bottle .. Look at it! *shakes head*
Now your mod/device has a va-jay-jay
Yes
Oh we understand your problem quite well.
We've seen this issue before.And we are trying to help you.
EDIT: STARTING TO WONDER IF THIS IS A PBCAC/PEBCAK ISSUE
The arc is just a spark - electricity jumping from contact to contact before they touch. Problem is it leaves a little black char, which interferes with future conductivity, so you want to remove that.
With the Armageddon, I got some arcing, and attributed it to having such low voltage drop (which is good) that the mod really wanted to contact and fire.
I have found that DeOxit gold works wonders to eliminate arcing. Literally a single drop on a bit of paper - slide that between contacts, press button, and slide it out (sorry - do this with no battery in...). This will both remove the black char, and coat the contact, improving conductivity and preventing arcing for a while.
I do NOT recommend sandpaper, as regular paper paper works to clean these contacts - while sandpaper, as mentioned, will remove the silver and permanently reduce the performance.
With the Armageddon, I got some arcing, and attributed it to having such low voltage drop (which is good) that the mod really wanted to contact and fire.
I have found that DeOxit gold works wonders to eliminate arcing. Literally a single drop on a bit of paper - slide that between contacts, press button, and slide it out (sorry - do this with no battery in...). This will both remove the black char, and coat the contact, improving conductivity and preventing arcing for a while.
I do NOT recommend sandpaper, as regular paper paper works to clean these contacts - while sandpaper, as mentioned, will remove the silver and permanently reduce the performance.
Wait up.
How badly is that fire button sticking?
Is it staying in the firing position after you let go of the button?
Random thought coming up...Did anybody besides me notice we were on page 666?
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
If your garbage pick up is free, go for it
It's well below mediocre - it is almost unvapable
?Huh?
Feel like I must have missed something here.
Tried the coral at my friends shop recently and it was (Meh) at best and burnt + spitty at worst.I'd rather go back to using CE4's than use the coral honestly.
Just wished I had remembered to grab my Haku-Clone on the way out the door...Sigh!
Yeah so my point is that we can buy the entire kit for LESS than FT sells just the mod from a US seller. Cheaper, plus we will receive it sooner...just toss the Coral and slap another rda on. Bingo bongo, done. No need to buy from FT until this place runs out of stock.
km00
Member For 4 Years
If shipping wasn't three times what the bottles cost, I'd send them your wayThat is lovely
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Wavered between the Luna & Luxotic this afternoon.. not much of a stabwood guy, that black honeycomb was calling out to me louder
; )
Opted for the silver / yellow kit on Fasttech, the Chinascus bottom plate & yellow bottles.
Then got the black honeycomb door / driptip set on 3FVape since I had some other little sh!ts in a cart there.
Also got to the post office for @BrewBear and others too finally...A good vape day all around.
; )
Annnd... got some work done finally too !
I'm SO ready for the weekend.. bring it ON.
Who has it on the cheap? I might get a couple more
Per snake94115’s post:
https://www.ecigvaporstore.com/product/ismoka-eleaf-istick-pico-squeeze-kit/ref/4/
Use the code “vapecrawler10” to get another 10% off.
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Last edited:
I believe that is where I ordered 2 more Dripbox2's from.
Yep just checked.
Under $17 each if I recall.
Just looked and no more Dripbox2's.
Yep just checked.
Under $17 each if I recall.
Just looked and no more Dripbox2's.
Last edited:
And I think that $40 is their free shipping break point.
I was a bit short so I threw in a Kanger Kbox mini Platinum.
Yeah I know not white but silver is ok
Like my Coppervapes.
I was a bit short so I threw in a Kanger Kbox mini Platinum.
Yeah I know not white but silver is ok
Like my Coppervapes.
Damn!
This will create an international incident!
This will create an international incident!
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
I'm sending a telegram to the Queen and calling Donald Trump!!!
Just call Todd. Isn't he royalty?
You go JL, let them have it!
I opted to get my Pico squeezes from FT, I refuse to buy from a place where you must meet a minimum purchase requirement before they give you a shipping option. The place linked to above had the Pico kit for $15.90 but you have to get $30 more crap for the cart to show a shipping option. No thanks.
Yep the DB2's may well be my only order from them.
Got an email saying that it all had shipped though.
Wonder where they are?
I believe they're in Miami.
Speaking of Todd.
Watch his last Vlog?
he had one word to say about the recent vape drama
Watch his last Vlog?
he had one word to say about the recent vape drama
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
One should always hold their idol blameless - you know that!!
I just didn't feel like driving 14 miles through a blizzard to get to town tomorrow
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
Speaking of Todd.
Watch his last Vlog?
he had one word to say about the recent vape drama
Let me guess
Bollocks?
You could get out the Cat Sled?One should always hold their idol blameless - you know that!!
I just didn't feel like driving 14 miles through a blizzard to get to town tomorrow
Contracts....Let me guess
Bollocks?
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
JuicyLucy
My name is Lucy and I am a squonkaholic
VU Donator
Diamond Contributor
ECF Refugee
VU Challenge Team
Member For 5 Years
While all the pusskins are glad I vape instead of smoke - they would say bollocks to that