temptingOk now THIS is my kinda deal. Got two boxes and a set of flush cutters and shipping was only 3 and a half bucks.
Best price I've seen yet, shipping is dirt cheap and LV is stateside. That's what I needed to see.tempting
I have 3 packs SS and 2 packs KA, also 2 more SS coming w/ Gunmetel Unity Tues..Best price I've seen yet, shipping is dirt cheap and LV is stateside. That's what I needed to see.
Well that's a no brainer then.I have 3 packs SS and 2 packs KA, also 2 more SS coming w/ Gunmetel Unity Tues..
It looks like that sale is over.Ok now THIS is my kinda deal. Got two boxes and a set of flush cutters and shipping was only 3 and a half bucks.
I don't have the patience for FT, 8 vape has them for $8.88im just waiting on slowtech https://www.fasttech.com/p/9703237
3 pack each $35.99 use Code:MAP gets about 50% off so i ordered a second pack
Still on preorder but i have some A! and a sample of Vandy mesh 200 to hold me over
Got my gunmetal Unity today so all is Matchy matchy on the Paranormal...ok. I just rewiccked with WoToFo cotton thingy's. using it now, with a very low tank =so it don't leak all over.
A little juice an it will work itself in. One of mine was like that and wore itself in.....been using it since I posted. it has leaked "0". and it hits pretty good with nice flavor. no dry hits yet at 50w.
I am liking it. except for the GD cap . after it has been on a while, it welds itself on, and I hardly lock it closed. mind you, I have a pretty good grip, but it feels like it was tightened with a pipe wrench.
they might but i got 6 boxes for the cost of 3 eightvape cost is way higher then that.I don't have the patience for FT, 8 vape has them for $8.88
A little juice an it will work itself in. One of mine was like that and wore itself in.....
I don't have the patience for FT, 8 vape has them for $8.88
The key word is "patience" or my lack of. I drive myself crazy checking for shipping hourly, I figure, my time and sanity is worth something.they might but i got 6 boxes for the cost of 3 eightvape cost is way higher then that.
I did, now I have about ten years worth, beyond my the average life expectancy of a American male....that's why you buy them before you need them.
No, then again I might be vaping it more than I had previously.(I didn't read this whole thread)
has anyone noticed this thing is pretty frugal on juice ?
I have found with the SS mesh I need wick it a bit heavier. Start with heavier Pom Poms, if not wicking fast enough, you can always trim them after. Dont be discouraged I have had occasionally leaks especially when I top it off.I knew I could do it ! I just rewicked it, and it's leaking, badly !
I have found with the SS mesh I need wick it a bit heavier. Start with heavier Pom Poms, if not wicking fast enough, you can always trim them after. Dont be discouraged I have had occasionally leaks especially when I top it off.
This what I have been doing. I use COTN lump ($2.99 @ eightvape) Divide the cotton in half, Trim to a little beyond the inside ring. Comb lightly. and from the bottom of the cotton fill the juice port completely but not tight. the cotton should extend no more than halfway down the port. Trim the rest of the cotton, which should be the majority of the wick to the outside of the inside ring, comb lightly and trim all strays and the sides. Works everytime. It will look like it will flood but with all that cotton it will wick lie a dripper. This seems to work for me better than all previous experiments and skips the cutting at an angle method.this time i didn't use the wotofo cotton stick. I pulled some cotton out of my stash. and I had it in there there pretty darned heavy, with poms so big I could hardly get the thing together. I'm thinking I may have pulled something apart assembling it.
It takes a few attempts to master it`. The important thing is those lower ports, if it is too tight it will not wick quick enough....ok. I vaped it down as much as I dared. took the deck out. low and behold, the wicking had somehow not filled the ports from side to side. I am using it now and it seems fine, so far.
It takes a few attempts to master it`. The important thing is those lower ports, if it is too tight it will not wick quick enough....
just top throw it out there, here's how I have mine wicked right now. 75 watts all day. No dry hits and no leaking/flooding.
View attachment 143664
http://vapingunderground.com/threads/new-profile-unity-rta.468673/page-3#post-2467087what cotton, and any not wet pics ? TC ?
mine is not leaking any more. but I am getting dry hits @50w. I have to take the cap loose for a few seconds.
I use this wicking method. He does a lot of explaining. Works perfect.what cotton, and any not wet pics ? TC ?
mine is not leaking any more. but I am getting dry hits @50w. I have to take the cap loose for a few seconds.
Exactly....and the rda is wicked oppisite.The two main keys with this rta are full, but not too tight in the bottom ports and make sure the little holes in the bell cap are covered by cotton, but not TOO tight there either. Next time I'm going to trim the outer top edge of the top poms poms and an angle. that's not needed there. It's fiddly at first, but pretty easy after you get it figured out. Unlike the rda which almost put me in a mental institution.
You are going to like it.....I got my .15 OFRF SS strips the other day, but haven't had a chance to try em yet. They do look brilliantly conceived for mesh TC. I hope so.
You don't like it?I'm going to be listing my gunmetal Unity here for sale, just as a heads-up.
Resist !!!!!!I'm going to be listing my gunmetal Unity here for sale, just as a heads-up.
Resist !!!!!!
This is the same pic as from above with the top of the wick digitally trimmed. I promise you, you do it like that and you will get no leaks or dry hits unless you chain vape it to death. Like I said up there. I ran that build at 75 watts all day with no problems and great flavor and vapor production. This is coming from somebody who had no end of woe with the Profile rDa.I have such issues with wicking this damn thing. I make the pom poms, etc etc etc the thing leaks like an old man's bladder. I'm over it.
I just cut an angle and stuff the wotofo cotton in there. I'm really suprised you're still having trouble man. I hate that for you. I put that as my top rta hands down.I have such issues with wicking this damn thing. I make the pom poms, etc etc etc the thing leaks like an old man's bladder. I'm over it.
I wonder if the problem is because I use rayon wicking. It doesn't swell up like cotton does when wet, rather it collapses.
just to throw it out there, here's how I have mine wicked right now. 75 watts all day. No dry hits and no leaking/flooding.
View attachment 143664
Don't think rayon is a good fit for the Unity design. I had leaking issues with rayon, worked fine with cotton, give that a try. I just got tired of washing all those parts and it gave me nothing better than the rda. Rda has better flavor and easy to deal with for me.I wonder if the problem is because I use rayon wicking. It doesn't swell up like cotton does when wet, rather it collapses.
After your frustrations with the rda, I'm glad to see you can get the rta to run the higher watts you wanted.This is the same pic as from above with the top of the wick digitally trimmed. I promise you, you do it like that and you will get no leaks or dry hits unless you chain vape it to death. Like I said up there. I ran that build at 75 watts all day with no problems and great flavor and vapor production. This is coming from somebody who had no end of woe with the Profile rDa.
View attachment 143960