Humm, looks like it meets all my requirements for a tank now. You guys think you unscrew the bottom to fill now? Or unscrew top?
I removed the bottom air screws and plugged them with epoxyThe main thing I don't like about the billow is being fixed it sounds like! Those air flow control screws on the bottom are junk so I'm glad to see those go! Will be impaitiently awaiting for the V2 to come out!
I removed the bottom air screws and plugged them with epoxy
Ordered as well. That's to avoid the Goliath's problem. Fine tuned wick jobs come apart when the tank/chimney is unscrewed. The inner chamber wall will keep things tidy!Looks like a win. I wonder why they did that second chimney piece.
Sent from my iPhone using Tapatalk
Ordered as well. That's to avoid the Goliath's problem. Fine tuned wick jobs come apart when the tank/chimney is unscrewed. The inner chamber wall will keep things tidy!
Had the Goliath for a few days and I'm loving it but it seems like I'll always be messing with the wicks every refillThat's to avoid the Goliath's problem. Fine tuned wick jobs come apart when the tank/chimney is unscrewed. The inner chamber wall will keep things tidy!
My thoughts too. I use my V1 Billow like a clearo, i screw off the base and then just dump my juice in. And now they made it even easier! Looks like a winner.Ordered as well. That's to avoid the Goliath's problem. Fine tuned wick jobs come apart when the tank/chimney is unscrewed. The inner chamber wall will keep things tidy!
zero leakage is a big plus
I've got dual parallel 26ga 16 wraps, 2.5mm center. Ohms out at 0.28, wicks touching the bottom of the large juice wells but not into the small ones. It's very good, enough to put the billow 1 down for a while, but not rediculous. What's the specs for your build?This'n is a keeper. First build I was concerned. I made some coils on 3mm center and somehow managed to get'm up and running. But, that didn't leave enough room for airflow so the vape suffered. But with coils on 2mm centers ... she's the best I've had in a tank. Kills me that the premades supplied were wound on 3mm centers ... sorta led me down a perilous path with those supplied coils, but I found my way to smaller coils and Billow Bliss.
Now I want two more in black.
I've got dual parallel 26ga 16 wraps, 2.5mm center. Ohms out at 0.28, wicks touching the bottom of the large juice wells but not into the small ones. It's very good, enough to put the billow 1 down for a while, but not rediculous. What's the specs for your build?
Your a bad influence on me bro. In a good way, of course!It's a beast! Very happy with it so far. We both have a dual parallel build 26ga 16 wrap on 2.5mm. Thing chucks the clouds at whatever wattage you throw at it (up to 100w so far). 5ml capacity, easy fill. I don't see leaking being an issue. Rocking 95% VG at very high wattage is not an issue.
Did my first build on the Billow v2 last night, just used the .6ohm coils that came with it.
I have zero leaking, but over like 40 watts, got a little burny. Think I'll pull it apart and rewick, I have the wick a tiny bit too thick maybe, and I've seen pics of NOT running wick into juice channels, rather, wet it and make sure to cover where the juice will come IN, so it has a larger contact point with the wick itself. Looks like that'd wick way better!
Tastewise, not sure it's as good as my crown, but i'm just starting to mess with it so that may change.
Build-wise, this is one sharp and well built tank!
Been doing 24g SS, 2.8MM ID about 7/8 wraps with an Rt of 0.21ohms