I decided to make up a thread dealing with questions I get on setting up a DNA200. I hope others will add anything they think is relevant.
1. How to add new TC wire to the material tab:
To add a new TC wire you can download the TFR table from Steam Engine as a CSV file to your PC located here. Click on the drop-down box and select the wire material you are interested in. Then click on the DNA200 tab above the drop-down box and finally click the download TFR table as CSV tab below and to the right (pay attention to where you are saving it to on your PC).
Then go to your material tab and click on the + button to add a new material. Then you would click on the un-named material you just added, then click the next button to the right of the + tab which is the open material button. Then navigate to where it (the CSV file) was saved on your PC and click on the CSV file and open. That's the way to add a curve instead of a single TCR number. Hope that wasn't confusing. That's the way I do it. It names it for you from the CSV file.
2. How to add custom screens:
Download the ones you like to your PC (make note of where you have saved them to). Hook up your DNA200 mod to Escribe and select the theme tab. Find the screen slot you want to change and click on load. Navigate to where you saved the screen on your PC and click on it then click on open. Finally click on Upload Settings to Device tab at the top of Escribe. Now you will be able to change any screens you want. That is also how you add custom screens to your 8 profiles only it's done in the General Tab.
PS Here's a link to where you can download a ton of custom screens and themes. It's on Google drive and sometime I get a 500 error, just refresh and it will eventually load.
3. Do I need to run The Battery Analyzer.
While I always think it's the best way to go if you have the time and correct resistor, it's not absolutely necessary. You can go to the mod tab and click on the Watt Hour Calculator. Then fill in the mah rating of your Lipo pack and it will calculate the Watt Hours and ask if you want to use this value, click Yes.
PS You want Lithium Polymer selected for Lipo packs or 18650's. Three cells unless you are running a 2 x 18650 DNA200 mod
4. Why can't see my charging screens while charging?
Most DNA200 mods come with the charging brightness set to 0. To change this go to the Screen tab in Escribe (with your mod hooked up) and increase the brightness from 0. I use 50-60% (I have old eyes
). Set it to whatever you prefer. This is where you can also change the screens you see while in running and charging mode. There are a lot to choose from
.
IMPORTANT: DON'T FORGET TO CLICK ON THE "UPLOAD SETTINGS TO DEVICE TAB" AT THE TOP OF ESCRIBE WHEN YOU ARE DONE MAKING CHANGES IN ORDER TO SAVE YOUR CHANGES TO YOU MOD.
Here's a link to the thread that discusses the new test firmware Evolv released, including a link to download it.
I'll add to this post as new things come to mind
Cheers,
Steve
1. How to add new TC wire to the material tab:
To add a new TC wire you can download the TFR table from Steam Engine as a CSV file to your PC located here. Click on the drop-down box and select the wire material you are interested in. Then click on the DNA200 tab above the drop-down box and finally click the download TFR table as CSV tab below and to the right (pay attention to where you are saving it to on your PC).
Then go to your material tab and click on the + button to add a new material. Then you would click on the un-named material you just added, then click the next button to the right of the + tab which is the open material button. Then navigate to where it (the CSV file) was saved on your PC and click on the CSV file and open. That's the way to add a curve instead of a single TCR number. Hope that wasn't confusing. That's the way I do it. It names it for you from the CSV file.
2. How to add custom screens:
Download the ones you like to your PC (make note of where you have saved them to). Hook up your DNA200 mod to Escribe and select the theme tab. Find the screen slot you want to change and click on load. Navigate to where you saved the screen on your PC and click on it then click on open. Finally click on Upload Settings to Device tab at the top of Escribe. Now you will be able to change any screens you want. That is also how you add custom screens to your 8 profiles only it's done in the General Tab.
PS Here's a link to where you can download a ton of custom screens and themes. It's on Google drive and sometime I get a 500 error, just refresh and it will eventually load.
3. Do I need to run The Battery Analyzer.
While I always think it's the best way to go if you have the time and correct resistor, it's not absolutely necessary. You can go to the mod tab and click on the Watt Hour Calculator. Then fill in the mah rating of your Lipo pack and it will calculate the Watt Hours and ask if you want to use this value, click Yes.
PS You want Lithium Polymer selected for Lipo packs or 18650's. Three cells unless you are running a 2 x 18650 DNA200 mod
4. Why can't see my charging screens while charging?
Most DNA200 mods come with the charging brightness set to 0. To change this go to the Screen tab in Escribe (with your mod hooked up) and increase the brightness from 0. I use 50-60% (I have old eyes
). Set it to whatever you prefer. This is where you can also change the screens you see while in running and charging mode. There are a lot to choose from .
IMPORTANT: DON'T FORGET TO CLICK ON THE "UPLOAD SETTINGS TO DEVICE TAB" AT THE TOP OF ESCRIBE WHEN YOU ARE DONE MAKING CHANGES IN ORDER TO SAVE YOUR CHANGES TO YOU MOD.
Here's a link to the thread that discusses the new test firmware Evolv released, including a link to download it.
I'll add to this post as new things come to mind
Cheers,
Steve
Last edited:
