Become a Patron!
Deathtrap by Deathwish?
- Thread starter Toniee3
- Start date
I have only recently seen it on a few sites. Mostly authentics being sold, though there is one or two sites already selling clones. Otherwise I don't think anyone on here has reviewed it yet.
Personal opinion based on looks. It's big, looks like a beast, makes sense in my mind about the squonking and the deck. Could be good, but don't quote me on that.
Personal opinion based on looks. It's big, looks like a beast, makes sense in my mind about the squonking and the deck. Could be good, but don't quote me on that.
I havent vaped mine yet...I dont have a series box big enough to comfortably use it at the moment...I could try it on a Stacked Tube I guess though..
It has a amazing build quality, love the machining on it...the clone Ive seen for it isnt anywhere near a 1:1...so if you want a Death Trap your going to have to spend that money they cost. The clams are 1/3 wider then the Goon 1.5 clamps and open up to 3.4mm in hieght, just shy of the Goon 1.5 clamp height opened.
Check out the Machining on this baby!!
The Juice well is more like a personal swimming pool with a deep section in the center. Ive made coils over a Inch in ID and they seem small still in the vast amount of space. There is front and back airflow for the coil(s) you install but you can cut off the front completely and adjust the rear independently.
The XXX Drip Tip it comes with is great. Its $30 if you were to buy just the tip...I like it on my Sherman RDA and it covers the entire top of the Skill/Druga/Goon and KEnnedy RDAs and its extremely smooth and comfortable.
Just one of the few things Ive tossed in it so far..
This build wouldnt fit in the Goon 1.5 or the Merlin RDTA, these 2 Toppers had the Largest holding capacity of any RDA/RTA/RDTA until the Death Trap was released. The margin of difference in capacity (Lead Width) isnt minute....its extravagant. You could take a Goon Clamp (widest sides) and clamp down on it in the deathtrap and there would still be a small bit of room on either side of the clamp and stack 3 of them also without a problem.
This build below wouldnt fit in the Goon 1.5, even with a screw removed as it would touch the topcap, even if I could of clamped on it I wouldnt have gotten more then 2 wraps to fit inside the cap. The Coils ID is 4mm....thats massive. Yet in the Death Trap it looks like its tiny AF!!!
My version of a "Double Barrel" Staggerton...basically 2 Staggertons side by side as one wire.
This Beast of a RDA is for people that are Serious about building, people that love Series Mods, or the Cloud Machine...there isnt much about this RDA I dont like...Kinda want the 4 Horseman HOG 3.1 now for it...
It has a amazing build quality, love the machining on it...the clone Ive seen for it isnt anywhere near a 1:1...so if you want a Death Trap your going to have to spend that money they cost. The clams are 1/3 wider then the Goon 1.5 clamps and open up to 3.4mm in hieght, just shy of the Goon 1.5 clamp height opened.
Check out the Machining on this baby!!
The Juice well is more like a personal swimming pool with a deep section in the center. Ive made coils over a Inch in ID and they seem small still in the vast amount of space. There is front and back airflow for the coil(s) you install but you can cut off the front completely and adjust the rear independently.
The XXX Drip Tip it comes with is great. Its $30 if you were to buy just the tip...I like it on my Sherman RDA and it covers the entire top of the Skill/Druga/Goon and KEnnedy RDAs and its extremely smooth and comfortable.
Just one of the few things Ive tossed in it so far..
This build wouldnt fit in the Goon 1.5 or the Merlin RDTA, these 2 Toppers had the Largest holding capacity of any RDA/RTA/RDTA until the Death Trap was released. The margin of difference in capacity (Lead Width) isnt minute....its extravagant. You could take a Goon Clamp (widest sides) and clamp down on it in the deathtrap and there would still be a small bit of room on either side of the clamp and stack 3 of them also without a problem.
This build below wouldnt fit in the Goon 1.5, even with a screw removed as it would touch the topcap, even if I could of clamped on it I wouldnt have gotten more then 2 wraps to fit inside the cap. The Coils ID is 4mm....thats massive. Yet in the Death Trap it looks like its tiny AF!!!
My version of a "Double Barrel" Staggerton...basically 2 Staggertons side by side as one wire.
This Beast of a RDA is for people that are Serious about building, people that love Series Mods, or the Cloud Machine...there isnt much about this RDA I dont like...Kinda want the 4 Horseman HOG 3.1 now for it...
I havent vaped mine yet...I dont have a series box big enough to comfortably use it at the moment...I could try it on a Stacked Tube I guess though..
It has a amazing build quality, love the machining on it...the clone Ive seen for it isnt anywhere near a 1:1...so if you want a Death Trap your going to have to spend that money they cost. The clams are 1/3 wider then the Goon 1.5 clamps and open up to 3.4mm in hieght, just shy of the Goon 1.5 clamp height opened.
Check out the Machining on this baby!!
The Juice well is more like a personal swimming pool with a deep section in the center. Ive made coils over a Inch in ID and they seem small still in the vast amount of space. There is front and back airflow for the coil(s) you install but you can cut off the front completely and adjust the rear independently.
The XXX Drip Tip it comes with is great. Its $30 if you were to buy just the tip...I like it on my Sherman RDA and it covers the entire top of the Skill/Druga/Goon and KEnnedy RDAs and its extremely smooth and comfortable.
Just one of the few things Ive tossed in it so far..
This build wouldnt fit in the Goon 1.5 or the Merlin RDTA, these 2 Toppers had the Largest holding capacity of any RDA/RTA/RDTA until the Death Trap was released. The margin of difference in capacity (Lead Width) isnt minute....its extravagant. You could take a Goon Clamp (widest sides) and clamp down on it in the deathtrap and there would still be a small bit of room on either side of the clamp and stack 3 of them also without a problem.
This build below wouldnt fit in the Goon 1.5, even with a screw removed as it would touch the topcap, even if I could of clamped on it I wouldnt have gotten more then 2 wraps to fit inside the cap. The Coils ID is 4mm....thats massive. Yet in the Death Trap it looks like its tiny AF!!!
My version of a "Double Barrel" Staggerton...basically 2 Staggertons side by side as one wire.
This Beast of a RDA is for people that are Serious about building, people that love Series Mods, or the Cloud Machine...there isnt much about this RDA I dont like...Kinda want the 4 Horseman HOG 3.1 now for it...
Sooo you're saying it would look fantastic on my HOG
