Become a Patron!
Vaping Underground PIF Box ~ LIVE & IN PROGRESS~
- Thread starter Geauxst
- Start date
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Yeah only thing is the one I got has temp mode and I can set it for 430second cycles and it has not auto cutoff but that's just options to be honest any Aromamizer Nd that size will be better then steeping the old waysomething like this?
Sent from the lab in my basement of vapement
Sent from a Ghost town
Do you put the whole bottle in when you do it? Or do you do it by the tank
Sent from the lab in my basement of vapement
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
I mix everything usually I use the plastic bottles (don't use the clear hard plastic ones they melt) and I'll squeeze a little air out before I cap it to make a suction then shake the juice to get air bubbles all in the juice put it in and run it for a 8min cycle take it out uncap it squeeze it several times to get new air in the bottle rinse and repeat for 12 cycles total or about an hour and half after which I let it cool to room temperature usually by then its blended nicely. You can do multiple bottle I've done 10 50ml bottles at once in mine its not required to completely submerge them its more the vibration and heat that helps and even models without the heat mode will create heat after about 4 cycles
Sent from a Ghost town
I've been debating on getting one, but I've been reading about using a food dehydrater instead. Any thoughts or suggestions?
Sent from the bowels of a twisted mind
Sent from the bowels of a twisted mind
In temp control for SS you have to choose the titanium coil set and decrease your temp by 80 degrees and you should be fine
Sent from the lab in my basement of vapement
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Another thing is did you build spaced coils or contact coils you really should never fire any TC build in power mode and as far as what you used to vape at TC is a whole new ball game forget everything you've done with previous builds and research and learn TC builds I consider myself an advanced builder when it comes to coils and I had to step back and relearn everything about building when I swapped to TC builds. Its a bit of a learning curve but you will get it
Sent from a Ghost town
Koopor + has a SS mode. Check your TCR, your build, and your initial resistance.
Oddly enough I lowered adjusted the initial resistance and it seems better even though the resistance is now wrong. As far as build they were both contact coils. What it seems like is that it's firing at a higher power than it should be for the resistance. A .5 coil fired at 35-40 watts is going to be pretty hot. I adjusted the TCR all up and down, I played with the min,soft,norm,hard modes. It's now vapable since I changed the initial resistance to .47 even though it's really a .54 coil. Even with that change my range seems to be 220-240 before it's goes back to burnt taste and no flavor. I suppose part of my question is if for temp control I need to be building lower even with SS.
When building TC coils, always used spaced coils. Contact coils hold heat longer and throw off resistance readings...
@Geauxst what temp do you keep the ultrasonic on and you said something about plastic bottles that are clear and hard melt so the PE ones are fine or should I just keep it in glass then transfer it to plastic after. You know that I'm going to try and put most "waterproof" things in there haha small things amuse me what can I say.
Sent from the lab in my basement of vapement
Sent from the lab in my basement of vapement
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Get rid of the contact coil go with spaced coils use a small screw to wrap on it makes it super easy to keep it even and also most TC coils run .05 not .5 like I said TC coils are a whole new ball game
As Shawn stated the coils are holding heat also if you are building on the mod you have to take it off and let it sit for 5 mins to return to room temperature best option is not to build on the mod so it doesn't confuse the chip and once again don't dry burn the coils... When you make TC coils you wrap them spaced they wick, wet, and test
Sent from a Ghost town
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
My US cleaner doesn't have a temp setting it just has a heat mode so I can't control it but I run heat for the first cycle or so then I run the rest no heat
As for the bottles you DIY a bit so you should know what I mean by this they have two type of bottles a hard clear plastic that is super hard to squeeze alot of concentrate flavors come in these like from rsv, myfreedomsmokes, fa .... Those melt under the heat
They they have a foggy unclear softer plastic that alot of vendor use for ejuice and like the unicorn bottles those will not melt they transfer the heat better
Gimme a min and I'll find the two I'm talking about you can see the difference
Sent from a Ghost town
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Left one bad it melts
Right one good never had a issue
I would suggest glass cause the glass ones the caps always vibrated loose on me but its all trial and error
Sent from a Ghost town
Lmao thank you I'm so much better with visuals
Left one bad it melts
Right one good never had a issue
I would suggest glass cause the glass ones the caps always vibrated loose on me but its all trial and error
Sent from a Ghost town
Sent from the lab in my basement of vapement
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Yeah me too
I figured the harder plastic would do better but its like putting it in fire even with the heat off it will deform it
Sent from a Ghost town
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Different how... Looks like a bottom airflow Atty kinda like freakshow
Has anyone else tried this bad boy I'm liking it and it's different it's the lancia
Sent from the lab in my basement of vapement
Sent from a Ghost town
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
I see... Not a fan of bottom fed airflow but I build my coils high so I've been getting bottom airflow for a long time
Sent from a Ghost town
Fine just rain on my frickan parade I'm taking my vape and going home
Sent from the lab in my basement of vapement
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Hey that's my opinion you don't have to like it or listen to itFine just rain on my frickan parade I'm taking my vape and going home
Sent from the lab in my basement of vapement
I like women doesn't mean you have to go all lesbian on us....
unless you are already a lesbian which I fully support and consider you as an equal in having the freedom of choice like the rest of us Sent from a Ghost town
I LIKE bottom air coils. Currently running a Fishbone, 571, Kennedy and Mutation V4 with bottom air flow.
I looked at the Lancia, but decided I didn't want to mess with dozens of parts...
I looked at the Lancia, but decided I didn't want to mess with dozens of parts...
Yes that is a downfall of it I have like a crafting tackle box it's where I keep all those type of things and all the orings I have and then I flip it over and it's all my screwdrivers and I wish I remembered where I got it
Sent from the lab in my basement of vapement
I was actually just looking at the glass that came with it because it's pretty close to being what you need
Sent from the lab in my basement of vapement
Ahh... hmmm...
Nope... Lancia glass is 22 mm o.d.
Art arrived Friday and I had time this weekend to crack the boxes open!
Here's what came in
I did have to toss out one partially filed bottle that leaked into it's baggie.
Here's what I took out
A few bottles of liquid, coil making tool, ohms checker, fuse and a sweet little atty for my low wattage single coil style!
And what I put in
I put in a bunch of liquids, TFA flavorings, a new Petit Gros hybrid 18350 mod, a 650mah Ego w/passthrough and a few other things. I'll be shipping it today to @builderbob
Here's what came in
I did have to toss out one partially filed bottle that leaked into it's baggie.
Here's what I took out
A few bottles of liquid, coil making tool, ohms checker, fuse and a sweet little atty for my low wattage single coil style!
And what I put in
I put in a bunch of liquids, TFA flavorings, a new Petit Gros hybrid 18350 mod, a 650mah Ego w/passthrough and a few other things. I'll be shipping it today to @builderbob
Cmd.Gio.420
Bronze Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Damn it so close since I watched your video I've been measuring all my glass to see if I could help you out.
Sent from the lab in my basement of vapement
Mal the Mello King
Bronze Contributor
Member For 4 Years
Member For 3 Years
Member For 2 Years
Member For 1 Year
Loland yes more pink lol
Sent from the lab in my basement of vapement
Sent from my iPhone using Tapatalk
Yep I used to have one I think that and the Maganus are some of the top flavor RDA's IMHO
Has anyone else tried this bad boy I'm liking it and it's different it's the lancia
Sent from the lab in my basement of vapement
I'm def more of a flavor person clouds I could care less about
Sent from the lab in my basement of vapement
Same another RDA that is cheap and kinda out of the mainstream that has amazing flavor is the Vulcan
Yeah... not necessary, but appreciated. I bought a Steam Turbine and then found another Caravela, which I also ordered.
And, speaking of videos and such, the new one is up...
Me too girl! I was not a fan of root beer but I'd definitely vape a bottle of that quick like! I think the "float" part is what helped, in my case anyway.
Yyyoooo... Mmmmmooooommmmaaaa!!! Lol... Hey Ms lady... Glad to see you back around these here parts
Wooooo Hoooooo....I can't wait!
Yes trying to get my phone setup and i miss my emojiis. I knew YOU would understand lmbo..Yyyoooo... Mmmmmooooommmmaaaa!!! Lol... Hey Ms lady... Glad to see you back around these here parts
)Sent from my SM-N900V using Tapatalk
Geauxst
A Banished Ghost of the Past
VU Donator
Gold Contributor
Member For 4 Years
Member For 3 Years
Download message plus it has themYes trying to get my phone setup and i miss my emojiis. I knew YOU would understand lmbo..
Sent from my SM-N900V using Tapatalk
Sent from a Ghost town