Become a Patron!

NEW - Steam Crave Hadron 220 / Dual 21700 mod /Powered by Yihi SX490

VinnySem

Silver Contributor
Silver Contributor
Member For 4 Years
I also posted about this over in the Steam Crave Mesh Deck thread:
Is anyone using the Hadron in temp control with SS mesh? I'm finding that when the mesh gets to temp, the mod starts rapid pulsing to maintain temperature. My DNA mods don't do this, and the Hadron doesn't produce a noticeable pulsing when using wire coils.


Sent from my iPhone using Tapatalk
 

TrollDragon

Silver Contributor
Member For 4 Years
ECF Refugee
I also posted about this over in the Steam Crave Mesh Deck thread:
Is anyone using the Hadron in temp control with SS mesh? I'm finding that when the mesh gets to temp, the mod starts rapid pulsing to maintain temperature. My DNA mods don't do this, and the Hadron doesn't produce a noticeable pulsing when using wire coils.


Sent from my iPhone using Tapatalk
Good old YiHi rattle snake action going on... It's normal and why I don't do TC on YiHi products, especially with YiHi boards that are not mainstream and specifically made for other manufacturers. SC should have gone with Evolv IMHO.
 

VinnySem

Silver Contributor
Silver Contributor
Member For 4 Years
Good old YiHi rattle snake action going on... It's normal and why I don't do TC on YiHi products, especially with YiHi boards that are not mainstream and specifically made for other manufacturers. SC should have gone with Evolv IMHO.
Agreed 100%. Going to keep the Hadron in wattage mode. For TC I'm spoiled by DNA mods and even my Hohm Slice with the FSK chip. I wish Hohm Tech would either license that tech or sell the boards to mod makers, that thing does fantastic TC.
 

VinnySem

Silver Contributor
Silver Contributor
Member For 4 Years
Is it possible to lock the resistance on the Hadron? I'm trying my SS316L wire in power mode, I'm noticing the resistance is being read again after firing and as SS wire does, the resistance increases as the wire is heated.
 

TrollDragon

Silver Contributor
Member For 4 Years
ECF Refugee
Agreed 100%. Going to keep the Hadron in wattage mode. For TC I'm spoiled by DNA mods and even my Hohm Slice with the FSK chip. I wish Hohm Tech would either license that tech or sell the boards to mod makers, that thing does fantastic TC.
I have 2 Wreckers and a Slice myself, they don't get much use these days though.
 

VinnySem

Silver Contributor
Silver Contributor
Member For 4 Years
Did you look in the manual? Look there 1st.

I did, there are instructions on locking the mod altogether, but not the resistance.

But good news, I've figured out how to mitigate the pulsing... it seems to be most noticeable when the wicking is packed a little too tight in the coil. I put a new build in my tank and it's barely noticeable now.


Sent from my iPhone using Tapatalk
 

Heartsdelight

VU Donator
Diamond Contributor
Member For 5 Years
I did, there are instructions on locking the mod altogether, but not the resistance.

But good news, I've figured out how to mitigate the pulsing... it seems to be most noticeable when the wicking is packed a little too tight in the coil. I put a new build in my tank and it's barely noticeable now.


Sent from my iPhone using Tapatalk
@VinnySem I found how to lock the resistance with ss316L.

Press middle button, as soon as the ohm value is visible on the screen, press the fire button to lock in the resistance.
 

Wb80

-DIY-demon-
VU Donator
Gold Contributor
Member For 4 Years
VU Patreon
Ty. I am waiting to give that a look over then buy a hardon and the squonk
 

VinnySem

Silver Contributor
Silver Contributor
Member For 4 Years
You’re welcome! :cheers:

Ok I found an issue with that method. If you adjust the watts, you have to hit the fire button to set the new power level, which then again reads the coil resistance. If you've just vaped on it, the coil is warm and resistance will be higher.


Sent from my iPhone using Tapatalk
 

Heartsdelight

VU Donator
Diamond Contributor
Member For 5 Years
Ok I found an issue with that method. If you adjust the watts, you have to hit the fire button to set the new power level, which then again reads the coil resistance. If you've just vaped on it, the coil is warm and resistance will be higher.


Sent from my iPhone using Tapatalk
Yep then you would have to wait again until the coil cools.
 

VU Sponsors

Top