hi there,
i recently bought a smoke stick v8 and i have 3 packs of m2 0.15 ohm coils (couldn't get the 0.25)..now i was worrying if i do something dangerous... even if they sell those things like "made for the stick v8" ..so if one uses ohms low ..it would mean on a direct 3.7 volt output with these coils..over 90 watt and around 25 Amps ..but i think it can't output more then 55 watts to the Atomizer)
i have seen some other threads where people were worrying about that..but it was not really clear in the end... (not to me ..lol)
so if i understood everything, it s like that : the stick v8 is a fully regulated mod , just not adjustable (which makes it even safer if understood right). and the main point is, so i understood, that i have two different circuits dealing with each other... the one from the controller to the battery and the one from the controller to the Atomizer (coilhead).. so Smok states, that the stick always fires around 3.7 Volt..which now makes sense to me ..so if it fires at 3.7 , the 3.7 is the constant and the rest ,like the wattage(don't know if the stick allows more than 60 W), varies then around a value which can feed the coil at the end.
so in the end it looks a bit like it doesn't matter at all, which coils i put into the atomizer (maybe they are all have the same safety doesn't matter which resistance)... the calculation would be necessary if you have a direct circuit with battery and atomizer in one..there the voltage would be the most important value i guess, because the discharge-ramp would depend directly from Battery Voltage and Atomizer-Resistance (Which is the only Parameter that can be controlled)...
i have to add ..the smoke stick v8 is a device from smoktech with a 3000 mAh Battery which like most other batteries can stand 20 Amps safely..
so from what i understand now, i am safe with the 0.15 coils..right ? (just if the regulation would fall out, if something like this would be possible)
an answer would be nice and sorry for my poor english
kind regards
i recently bought a smoke stick v8 and i have 3 packs of m2 0.15 ohm coils (couldn't get the 0.25)..now i was worrying if i do something dangerous... even if they sell those things like "made for the stick v8" ..so if one uses ohms low ..it would mean on a direct 3.7 volt output with these coils..over 90 watt and around 25 Amps ..but i think it can't output more then 55 watts to the Atomizer)
i have seen some other threads where people were worrying about that..but it was not really clear in the end... (not to me ..lol)
so if i understood everything, it s like that : the stick v8 is a fully regulated mod , just not adjustable (which makes it even safer if understood right). and the main point is, so i understood, that i have two different circuits dealing with each other... the one from the controller to the battery and the one from the controller to the Atomizer (coilhead).. so Smok states, that the stick always fires around 3.7 Volt..which now makes sense to me ..so if it fires at 3.7 , the 3.7 is the constant and the rest ,like the wattage(don't know if the stick allows more than 60 W), varies then around a value which can feed the coil at the end.
so in the end it looks a bit like it doesn't matter at all, which coils i put into the atomizer (maybe they are all have the same safety doesn't matter which resistance)... the calculation would be necessary if you have a direct circuit with battery and atomizer in one..there the voltage would be the most important value i guess, because the discharge-ramp would depend directly from Battery Voltage and Atomizer-Resistance (Which is the only Parameter that can be controlled)...
i have to add ..the smoke stick v8 is a device from smoktech with a 3000 mAh Battery which like most other batteries can stand 20 Amps safely..
so from what i understand now, i am safe with the 0.15 coils..right ? (just if the regulation would fall out, if something like this would be possible)
an answer would be nice and sorry for my poor english
kind regards