Good builds for an unregulated series box.

So, I built a series box, but I'm kinda struggling to find a good build for it. I'm looking to either build something on my Lycan or my DogeX v1. Right now, I have dual 10 wrap 26ga Chromel-c coils, but it's a bit excessive. And while I'm looking at giving up cloud chasing, I would still like to know some good series builds to do it with. I am pretty happy with the flavor of the current build, but it's hitting .7 ohm, and I know that's higher than I really need to go.
So, do you wonderful folks have any suggestions?

On my Nasy box mod with a Kennedy atty I run 4 to 5 wraps 24g around about 2mm to 2.5mm comes out to around .25 ohms that is where I vape on my box all the time.

I have been running on my Vulcan. Dual coil 26g twisted about 10 wraps runs a little warm about 50w but great taste

Thanks

biglenny1211 said:

On my Nasy box mod with a Kennedy atty I run 4 to 5 wraps 24g around about 2mm to 2.5mm comes out to around .25 ohms that is where I vape on my box all the time.

Click to expand...

this is also my regular set up

biglenny1211 said:

On my Nasy box mod with a Kennedy atty I run 4 to 5 wraps 24g around about 2mm to 2.5mm comes out to around .25 ohms that is where I vape on my box all the time.

Click to expand...

On an unregulated SERIES box you'd be asking for trouble vaping anything that low.

10 wrap 24 gauge on a 3mm ID is perfect for my series box.

Twisted 26g 7 wrap is perfect imo

Assuming you're using anything other than a VTC4/3 keep it above 0.5 ohms. It doesn't matter how you get there. If you do have a set of VTC4/3s you can go as low as about 0.3 ohms. However, that will be an absurdly hot vape at over 200 watts.

I am running a 26650 dual series box I built myself.....I do not like it when I start vaping and I get a dry hit with wet cotton in the juice well. I have raised my number of wraps on my rda until I can vape until my cotton is dry and totally dry with no burning.......being new to a series box it has taken patients to work it out......hang in there u will find the right build for you

Sent from my SCH-S968C using Tapatalk

I have a goon RDA on a noise cricket and I love this build I have in it. It's a 12 wrap 24 gauge kanthal or niacrom infinity/ Chuck Norris build on a 3mm bit. I've seen it on a YouTube as the infinity coil but I found it on a Google search as a Chuck norris coil. all it is, is a 12 wrap coil that you bend in the middle to get two virtical 6 wrap coils connected at the top. I keep the wick in one piece all the way through so there's a big cotton head on my coils. I got a .36 ohm reading and it Chuck's clouds with awesome flavor. I can vape it between 60-200 watts. The 200 is what I mathed out the coils are getting on the noisey cricket. Use 25 amp batteries at least as this build draws 23.33 amps according to my vape tool app. though I was using Samsung 25rs which are 20. I had no problems with them but I also didnt take the batteries below 3.8 because the thing hits hard and I got a huge nicotine buzz. I also did twisted quad strange 26 gauge niacrom 8 wraps 3mm bit. Came out .32 faster ramp up. Use 30 amp batteries for that build.

No

What do you mean no?

jennyyili said:

No

Click to expand...

What do you mean Jenny? No to what.

Number3124 said:

Assuming you're using anything other than a VTC4/3 keep it above 0.5 ohms. It doesn't matter how you get there. If you do have a set of VTC4/3s you can go as low as about 0.3 ohms. However, that will be an absurdly hot vape at over 200 watts.

Click to expand...

VTC3 is 28A and can go down to 0.3
VTC4 is only 23A and should not.

LG HB2/4/6 have the same capacity as a VTC3 but have better amp rating (30A)