Become a Patron!

Profile RDA

pkane11384

Member For 1 Year
Long story short,

Signed up for ZampleBox and decided to go back to dripping on my Profile so I wasn’t going through coils on the tank I’m using right now. Pull the coil and cotton rinse everything. Go to pull the squonk pin out and the whole assembly pulls out, threads and all. Once that pulls out the spring and one of the posts came with it. Can’t see any way to repair it either.

https://imgur.com/a/2j26196

Emailed Wotofo and the company I ordered it from and no response from either. Looks like I’ll have to look into a new RDA.
 

MrMeowgi

The Vapin' Drummer
VU Donator
Diamond Contributor
Member For 4 Years
I think the post press fit sort of. Most positive posts are replaceable. Should be able to just fit it back together and put the solid pin back in. Not sure when you contacted wotofo but don't forget they're in China. So completely different schedules
 

ajvapes

Gold Contributor
Member For 5 Years
VU Patreon
Long story short,

Signed up for ZampleBox and decided to go back to dripping on my Profile so I wasn’t going through coils on the tank I’m using right now. Pull the coil and cotton rinse everything. Go to pull the squonk pin out and the whole assembly pulls out, threads and all. Once that pulls out the spring and one of the posts came with it. Can’t see any way to repair it either.

https://imgur.com/a/2j26196

Emailed Wotofo and the company I ordered it from and no response from either. Looks like I’ll have to look into a new RDA.
looks like the squonk pin is still in the 510 pin. You need to remove it from the shaft and reinstall the 510n assembly, then install the non squonk pin....
 

pkane11384

Member For 1 Year
looks like the squonk pin is still in the 510 pin. You need to remove it from the shaft and reinstall the 510n assembly, then install the non squonk pin....

It was Friday sometime. Not sure if they’re in their offices over the weekend so I should hear from them soon but nothing fro myvpro who I ordered from either. It’s been a few months since I ordered it so I’m not sure they’ll do anything but it’s worrh a shot.

I can’t think of any way to pull the squonk pin from the 510 pin without damaging the threads on it. Not sure how it wouldn’t leak either. Might chalk this one up as a loss.
 

ajvapes

Gold Contributor
Member For 5 Years
VU Patreon
I think the post press fit sort of. Most positive posts are replaceable. Should be able to just fit it back together and put the solid pin back in. Not sure when you contacted wotofo but don't forget they're in China. So completely different schedules
The 510 has a stepped thread, the larger diameter holds the positive post in, the smaller is for the spring and block.
 

ajvapes

Gold Contributor
Member For 5 Years
VU Patreon
It was Friday sometime. Not sure if they’re in their offices over the weekend so I should hear from them soon but nothing fro myvpro who I ordered from either. It’s been a few months since I ordered it so I’m not sure they’ll do anything but it’s worrh a shot.

I can’t think of any way to pull the squonk pin from the 510 pin without damaging the threads on it. Not sure how it wouldn’t leak either. Might chalk this one up as a loss.
Use a needle nose plier to hold the non threaded part and hex wrench to remove the sqounk pin from the bottom...
 
It was Friday sometime. Not sure if they’re in their offices over the weekend so I should hear from them soon but nothing fro myvpro who I ordered from either. It’s been a few months since I ordered it so I’m not sure they’ll do anything but it’s worrh a shot.

I can’t think of any way to pull the squonk pin from the 510 pin without damaging the threads on it. Not sure how it wouldn’t leak either. Might chalk this one up as a loss.

It was Friday sometime. Not sure if they’re in their offices over the weekend so I should hear from them soon but nothing fro myvpro who I ordered from either. It’s been a few months since I ordered it so I’m not sure they’ll do anything but it’s worrh a shot.

I can’t think of any way to pull the squonk pin from the 510 pin without damaging the threads on it. Not sure how it wouldn’t leak either. Might chalk this one up as a loss.

Believe you have to do this while assembled so to speak. I remember seeing some video somewhere that happened, I totally forgot to swap the pins and realized I was leaking juice all over my paranormal.... yeah Im like a kid opening an xmas gift at age 3 still....
 

VU Sponsors

Top